Fablestoryem Rebar Tying Tool, 8-34mm/30-60mm Automatic Rebar Tying Machine, Handheld Rebar Tie Rechargeable Rebar Tier Machine for Steel, Aluminum(1500mAh/13200mAh Lithium Battery X 2),8-34MM

• 【Rebar Tier Tying Machine】This rebar-tying machine is made of top-quality plastic and corrosion-resistant metal.The built-in pure copper motor, precise microcontroller, and top-quality binding wire allow 3000 knots to be tied when fully charged, and can be completed in just 0.8 seconds for each, saving 3-5 times more manpower than manual labor.The head positioning sleeve can be adjusted, allowing you to bind more accurately and firmly.
• 【2 Rechargeable Lithium Batteries】Rebar tier tying machine equipped with two rechargeable 12V lithium-ion batteries, and its battery capacity is 1500mAh(8-34mm-model) / 13200mAh(30-60mm-model), which is sturdy. You only need to charge it for an hour and a half to be fully charged, which can be tied up approximately 1500(8-34mm-model)/3000(30-60mm-model) times.
• 【Easy To Use】Rebar tier tying machine equipped with a steel wire groove, the use is simple and convenient. Just press the wire-out switch to work. The sharp knife edge cuts the wire more quickly, greatly improving the efficiency of strapping.
• 【Ergonomic Handle】 11.42 x 2.56 x 7.68inch small size, light weight, easy to grasp. The ergonomic non-slip handle design allows you to hold for a long time without feeling tired and makes your work easier.
• 【Wide Application】This hand-held rebar tying device is suitable for 8mm-34mm(0.3"-1.3" ) / 30mm-60mm(1.18-2.36" )steel strips, mainly used in the construction industry, such as house construction, floor pipes, heating floor nets, bridges, highways, etc.

Automatic Rebar Tier 8-34mm/30-60mm Handheld Rebar Bender Machine Handheld Rebar Tier Tool Reinforcing Steel Strapping Machine with Plier ►►Specification: - Color: Orange - Material: Plastic, Metal - Power Source: Battery Powered - Motor Type: Pure Copper Brush Motor - Battery Type: 12V Lithium-ion Battery - Battery Capacity: 1500mAh/13200mAh - Battery Full Charging Time: 1.5h - Tying Wire Length: 110m/360ft - Tying Wire Diameter: 0.8mm/0.03inch - Tool Type: Tier Tying Machine - Applicable Scope of Steel Strapping: 8-34mm(0.3-1.3inch) / 30-60mm(1.18-2.36inch) - Knot Wire Length: ≥35cm/13.7inch - Number of Knots: 1500/3000 - Required Knot Time: 0.8s Per Time - Cable Length: About 95cm/37.4inch - Machine Size: 290 mm x 65 mm x199 mm / 11.42 x 2.56 x 7.68inch - Toolbox Size: 42 x 29 x 11cm/16.5 x 11.4 x 4.3inch ►Package Included: - Rebar Tying Machine x 1 - Plier x 1 - Tying Wire x 1 Roll - Charger x 1 - Lithium-ion Batteries x 2 - Toolbox x 1 - English Manual x 1 ►►Installation instructions: 1. In the state of start-up, press the locking plate of the opening wire plate, open the plate cover. 2. Take out the tying wire, tear the packaging film, pull straight wire head about 10 cm, load into the binding machine in the clockwise direction, the wire head into the guide tap tube. 4. Cover the plate and fasten the locking piece. 5. Pinch the wire forward with two fingers, press and hold the switch and send the wire out. 6. If you want to take out the wire plate when finished, press and hold the locking piece, open the wire plate cover plate, holding the wire tray to the side and pull out. ►If you have any questions after receiving the package, please contact us as soon as possible, we will give you a satisfactory answer at any time.