DieseRC 3pcs 433.92Mhz Fixed Code Clone Remote Control Keychain RF Transmitter Only for Fixed Code Remote Control, Not for Rolling Code

• 【Great design】433Mhz RF Fixed Code Clone Remote Control（Rolling code remotes will not work!）. It is a duplicator which can clone other fixed code remote control. It can be controlled within 30 meters distance in open area.
• 【Wide coding range】2260,2262(such as PT2262, SC2262, HS2262, LX2262, HX2262, etc.),1527(EV1527, HS1527, HX1527, SC1527, GP1527, CP1527, AD1527, SCL1527, TL1527, ZX1527)PT2264, PT2240(LX2240, LX2241, SCL2240), CS5211, SMC918, AX5026, SMC926, AX5326-3, AX5326-4, FP527, HT600, HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F630, ULN2003.Although different chip manufacture has different chip model prefix, it will be OK, as long as the chip model numbers are same. ***Note: Rolling code remotes will not work!!! This only can copy fixed code.
• 【Notice before purchase】There are three conditions should be confirmed before purchased. ①The original remote control works normally.②The frequency should been 433.92Mhz. ③The chip Code(Encoder Chip) as listed. ④ ***Note: Rolling code remotes will not work!!! This only can copy fixed code.
• 【More Flexibility】 There are 4 buttons on the remote control which means you can clone 4 buttons. Each button operates independently. The clone remote control can reset and set up without limited times.

Package Include: 3x cloner remote controls Product manual Parameter: - RF frequency: 433MHz - battery: 1x 27A 12V (included) - Size: 55mm*30mm*14mm - Button: 4 Keys - transmitter range: Open space is more than 50 meters Please confirm three conditions before purchasing. 1: The original remote control works normally. 2: The frequency: 433.92Mhz. 3: The chip Code (Encoder Chip) as listed below 2260,2262,1527(EV1527, HS1527, HX1527, SC1527, GP1527, CP1527, AD1527, SCL1527, TL1527, ZX1527)PT2264, PT2240(LX2240, LX2241, SCL2240), CS5211, SMC918, AX5026, SMC926, AX5326-3, AX5326-4, FP527, HT600, HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F630, ULN2003 Note: Rolling code remotes will not work!!! Reset: Press and hold "A" and "B" keys together---Led will flash 3 times. And then release "B" key (meanwhile “A” key still holding on all the time) and click "B" key 3 times---Led will flashing and then light off. succeed. Programing 1. Put the original remote and cloner remote into "back to back" position. Make sure they have direct contact. Or the two remote controls should be placed as closely as possible (put the two remote controls on the desktop side by side with zero distance). 2. Press and hold one key on your original remote, and then press and hold one key on your cloner remote. Keep holding until LED will make 2 blinks (Notice: LED 2 blinks not to release button) Then 3 blinks then into steady and you have successfully cloned. If for some reason the clone does not go further than 2 blinks, it means the signal does not go through, please shift the remote slowly up and down until you get the point where it will go through. For the presence of noise, it should avoid interference to operate, if the copy is not successful, it should recopy after clearing code.