3 m 130 Watt 12 V Low Voltage Carbon Heating Film with Thermostat - Floor Heating in Caravan, Individual Projects, Battery Case Heating, Beehive Heating, Model Making

• 12 V low voltage 130 watt/m² heating film for use under floating floor coverings such as: laminate, parquet, planks, ship floor, linoleum, cork, carpet
• Ideal for the installation and retrofitting of an electric underfloor heating system in caravans, motorhomes, campers, tiny houses, boats, trucks, cars, camping vehicles, RVs, expedition vehicles, or similar vehicles
• Also suitable for individual projects: heating for battery cases, hive heating, model building, etc. for heating, heating or tempering
• Low investment costs | Low profile height of only 0.366 mm | Easy floating installation | Robust electric heater
• Includes matching 12 V M3 thermostat | 3 operating modes - off, eco mode, comfort mode | internal and external temperature sensor | display of set and actual temperature | operation on 12 V DC and AC voltage possible | powerful relay, load capacity up to 20 A / 240 W

The Mi-Heat low-voltage heating film is ideal for retrofitting and retrofitting an electric underfloor heating in caravans, motorhomes, caravans, campers, tiny houses, boats, trucks, cars, campers, motorhomes, expedition vehicles or similar vehicles. The heating film can be used for almost any project and also allows self-sufficient operation. The heat generated is transferred directly and evenly to the floor covering and thus ensures pleasantly warm feet. When installing the heating films in vehicles, the following points must be observed: The heating film can only be used in vehicles for temperature control of the floor. In order to raise the room air temperature, an additional heat source (auxiliary heaters such as Truma or Webasto). The heating film must not be laid in areas where fully lying furniture or objects with a diameter greater than 6 cm are located. The heating film can always be thermally monitored by means of a thermostat and external floor sensor. When using several heating foil sheets, they must be connected parallel to the thermostats. Please note the maximum switching capacity of the thermostat. Depending on the number of heating foils, Additional connection terminal required. In order to feel the heat generated, the heating film must be covered with a floor covering. For testing purposes, the heating film can also be partially covered. Do not use your palm to measure temperature, as it is about the same temperature as the surface temperature of the heating film. Use an infrared thermometer or a thermostat with floor sensor. The required settings can be found in the instructions of the thermostat. Depending on the current ambient temperature, a lead time of up to 60 minutes must be planned. Recommendation: Thanks to the use of our 1.5 mm heating film underlay, the efficiency of the heating film can be increased again. Technical data (heating film): Operating voltage: 12 V AC/DC. Max. Power consumption: 130 watts/m² (+/-10%). Panel width: 50 cm. Active range: 45 cm. Heating area per m²: 74%. IR wavelength: 7-14 microns Temperature resistant: up to 80 °C. Efficiency: 98%. Material thickness: 0.366 mm. Insulation: 2-ply, 1-way insulated. Technical data (M3 thermostat): mounting type: flush-mounted. Design: wired. Operating voltage: 12 V AC/DC. Max. Switching capacity: 20 A/240 W. Control type: two-point control on - off. Operating temperature: 5-50°C. Sensor: Internal & External Temperature control range (internal/room sensor): 5-95°C. Temperature control range (external/ground sensor): 5-95°C. Compatible NTC sensors: 10kOhm at 25°C Frost protection: yes, 5 °C. Floor limiting range: 5-60°C. IP protection class: IP20. Display/Lighting: Yes/Yes Dimensions: (W x H x D) 80 x 90 x 13/43 mm. Package includes: 1 x 12 V heating foil in selected length with assembled 2.5 m connection cable. 1 x thermostat M3-12 V including mounting accessories. 1 x floor sensor NTC 10 kOhm. 1 x user manual.